RS485 Adapter hardware 1.1

#!/usr/bin/env python3
"""
Minimal trapezoid move: rotate 1 turn in 1 second.
Edit ALIAS below if needed. Uses rotations and seconds.
"""
import time, servomotor
from servomotor import communication

# Hard-coded settings for a minimal demo
ALIAS = 'X'                             # Device alias, change if needed
SERIAL_PORT = "/dev/tty.usbserial-110"  # Serial device path; change if needed (e.g., "COM3" on
                                        #  Windows)
DISPLACEMENT_ROTATIONS = 1.0            # 1 rotation
DURATION_SECONDS = 1.0                  # 1 second
DELAY_MARGIN = 0.10                     # +10% wait margin because the motor's clock is not
                                        #  perfectly accurate

communication.serial_port = SERIAL_PORT # if you comment this out then the program
                                        #  should prompt you for the serial port or it will use
                                        #  the last used port from a file
servomotor.open_serial_port()

m = servomotor.M3(ALIAS, time_unit="seconds", position_unit="shaft_rotations", verbose=0)
m.enable_mosfets()
m.trapezoid_move(DISPLACEMENT_ROTATIONS, DURATION_SECONDS)
time.sleep(DURATION_SECONDS * (1.0 + DELAY_MARGIN))
m.disable_mosfets()

servomotor.close_serial_port()

// Minimal Arduino example: Trapezoid move using built-in unit conversions
// Goal: spin the motor exactly 1 rotation in 1 second, then stop.
// Sequence:
//  system reset -> enable MOSFETs -> trapezoidMove(1.0 rotations, 1.0 seconds)
//  -> wait 1.1s -> disable MOSFETs.
//
// Notes:
// - This uses the library's unit conversion (no raw counts/timesteps).
// - Configure Serial1 pins for your board (ESP32 example pins below).
// - Motor is created AFTER Serial1.begin(...) so hardware UART pins are set first.
// - Every command is checked with getError(). No command method returns a success
//   flag, and a motor that has latched a fatal error silently ignores everything
//   afterwards, so an unchecked sketch just stops moving with no symptom at all.
//   See "Checking for errors" in the API documentation.

#include <Servomotor.h>

#define ALIAS 'X'                   // Device alias
#define BAUD 230400                 // RS485 UART baud rate
#define DISPLACEMENT_ROTATIONS 1.0f // 1 rotation
#define DURATION_SECONDS 1.0f       // 1 second
#define TOLERANCE_PERCENT 10        // +10% wait margin because the motor's clock is not
                                    //  perfectly accurate
#define WAIT_MS ((unsigned long)(DURATION_SECONDS * 1000.0f * (100 + TOLERANCE_PERCENT) / 100))
#define POST_RESET_WAIT_MS 1500     // Keep the bus SILENT this long after a reset: the motor
                                    //  boots through a bootloader window, and any packet that
                                    //  arrives during it pins the motor in the bootloader.

// Example RS485 pins for ESP32 DevKit (change as needed for your board)
#if defined(ESP32)
#define RS485_TXD 4              // TX pin to RS485 transceiver
#define RS485_RXD 5              // RX pin from RS485 transceiver
#endif

// Returns true (and explains itself) if the previous command did not succeed.
// getError() is 0 on success, positive for a fatal error reported by the motor
// (look the number up in the Error Codes section of the documentation), and
// negative for a communication failure such as -1 = no reply within 1 second.
bool failed(Servomotor &motor, const char *what) {
  int e = motor.getError();
  if (e == 0) return false;
  Serial.print("[FAIL] ");
  Serial.print(what);
  Serial.print(" -> getError() = ");
  Serial.print(e);
  Serial.println(e > 0 ? "  (motor fatal error - see the Error Codes section)"
                       : "  (communication failure - check wiring, alias and power)");
  return true;
}

void setup() {
  Serial.begin(115200); // Console serial for debugging
                        // On ESP32-S3, set Tools > USB CDC On Boot > Enabled or this
                        // output never reaches the USB serial monitor.

  // Create the motor; serial port opens on first instantiation.
#if defined(ESP32)
  Servomotor motor(ALIAS, Serial1, RS485_RXD, RS485_TXD);
#else
  Servomotor motor(ALIAS, Serial1);
#endif

  // Use units: rotations for position, seconds for time.
  // These are host-side only - they send nothing to the motor.
  motor.setPositionUnit(PositionUnit::SHAFT_ROTATIONS);
  motor.setTimeUnit(TimeUnit::SECONDS);

  // Start from a known-clean state: this also clears any fatal error left over
  // from a previous run, which is the usual reason a motor "stops working".
  motor.systemReset();
  if (failed(motor, "systemReset")) return;
  delay(POST_RESET_WAIT_MS);

  motor.enableMosfets();
  if (failed(motor, "enableMosfets")) return;

  motor.trapezoidMove(DISPLACEMENT_ROTATIONS, DURATION_SECONDS);
  if (failed(motor, "trapezoidMove")) return;

  delay(WAIT_MS);

  // A successful move command only means the move was accepted and queued. Faults
  // such as a stall or a position-deviation trip happen later, while it executes,
  // so check the motor's own status once the motion should be finished.
  getStatusResponse status = motor.getStatus();
  if (failed(motor, "getStatus")) return;
  if (status.fatalErrorCode != 0) {
    Serial.print("[FAIL] motor faulted during the move, error code ");
    Serial.println(status.fatalErrorCode);
    return;
  }

  motor.disableMosfets();
  if (failed(motor, "disableMosfets")) return;

  Serial.println("Move completed successfully.");
}

void loop() {
}